Then choose the correct rubber base for your rim type. Rims with a curved rim section will use the circular rubber base. Rims with a square rim section will use the square rubber base. Slot this on down to the bottom of the valve stem. (If you find your rim has a larger valve hole and the smaller circular fitment is too loose, use the larger circular fitment to plug the hole) Use the valve core removal tool (integrated into spare alloy cap) to remove the core and fill with no puncture hassle tubeless sealant and inflate! Job Done. Now Grab a tyre worm (you may need to use the tool to help slide out the worms). The largest size is for MTB tyres the medium for gravel tyres and the small for road tyres, but you can select the best one for your sized hole. Now pinch one end of the worm hard between your fingers to flatten it out. (If using the thin worm thread through the tip at the end of the tool, not the main larger slot) No, it is not fully waterproof however we have designed the system to encapsulate the AirTag as best as possible and the AirTags being placed inside are IP67 standard meaning they are water resistant. The Ultimate Tubeless kit is available in a range of options to suit different disciplines and their corresponding wheel sizes plus rim depths. I've been testing the Road/Gravel set for deep-section rims, which includes a 21mm x 10m roll of Muc-Off's own tubeless rim tape, two 60mm valves and two 140ml pouches of its No Puncture Hassle Tubeless Sealant.

In the kit you also get a selection of rubber grommits to make sure the valves sit leak-free in the hole, regardless of rim bed shape. Remove the tool from your bars using a 4mm Allen key. (If tool is pre-loaded skip to step 5) Start by using the integrated knurled reamer on the tool to clean and roughen up the hole to ensure a perfect seal. I've also tested the No Puncture Hassle sealant previously too, and it is right up there with the best on the market. I found that it lasted for about five months before it had dried out and needed to be replaced. Once your happy with how it looks using a small pin locate the valve hole and cleanly pierce the tape ready for the valveStart by unwinding a small amount of the tape and pressing it down using your thumb or finger to hold pressure down.

Over the course of 6+ months of extensive real-world testing inside many different wheels we haven't experienced any damage to the AirTag as a result of using the Tubeless Tag Holder. The built in sacrificial and compressive layer integrated into the system has been designed to ensure impacts are minimised to help protect your rim and the AirTag. With 5 available kits for: Road, Gravel & CX (Deep Rims), Road, Gravel & CX (Shallow Rims), X-Country, DH/Enduro and DH wide. We’ve covered all the bases when it comes to installing the ultimate high-performance tubeless setup. Directions for use: Unfortunately, it seems that all tyre sealants can stain! If No Puncture Hassle sprays on your kit out on the trail, try to rinse the affected area straight away with clean water from your bottle and then wipe off as soon as possible with a damp cloth. Less faffing, more shredding: of course, you'll spend less time fixing flats, so you’ll be first to the pub/ café stop! Must Have Tubeless AccessoriesFinally; No Puncture Hassle Tubeless Sealant performs under the most brutal race conditions. The cutting-edge molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. Their formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Please refer to the compatability section, however the narrowest recommended tyre size is 38c wide. If you are riding a road bike, we suggest you use our Secure Tag Holder instead. Tubeless tire setups have been around for a while now in the mountain bike scene, and are now becoming increasingly popular among gravel, and even road cyclists. It just makes sense. A tire that seals its own punctures is a pretty incredible thing. If you’re going to run a tubeless setup, you’ll definitely need the key ingredient that makes that magic happen: Tubeless Sealant. Looking to convert to tubeless? Our Ultimate Tubeless Setup Kit is a complete kit with every essential needed to join the tubeless revolution. What Are The Benefits of Making Your Bike Tubeless?